A Checklist Before You Order a Replacement Computer

A replacement computer is not a cheap part, and we would rather you bought one only when you actually need one. This is the checklist we would run through ourselves. It costs an afternoon and it regularly saves people from buying a part their vehicle did not need, or from killing a good new unit with a fault that was never fixed.

Work through it in order. Each section builds on the one before it.

Step 1: rule out the cheap things

The overwhelming majority of vehicles that arrive at a shop with a "bad computer" have something else wrong. Start here.

  • Battery load tested. Not a voltage reading on a meter, an actual load test. A battery can show 12.6 volts at rest and collapse under a starter. Most parts stores test for free.
  • Charging voltage checked with the engine running, and checked again with the headlights and blower on.
  • Battery terminals and ground straps cleaned and tightened, including the engine to body strap and the small ground wires bolted to the inner fenders, firewall and cylinder head. Clean to bare metal. A connection can look perfect and be bad underneath.
  • Every fuse and relay that feeds the computer checked. Use a wiring diagram rather than guessing, because most modules have more than one power feed, and some are only live with the key on.
  • The module connectors inspected for green or white corrosion, water, oil, bent pins, pins pushed back below their neighbours, and heat damage. Both sides, module and harness.
  • The 5 volt reference measured at an accessible sensor with the key on. If it is low, a single shorted sensor is taking several sensors offline and the computer is fine. See our post on the 5 volt reference.
  • Trouble codes written down exactly as the reader shows them, with freeze frame data if available, and noted as pending, confirmed or permanent.

If any of these turns up a problem, fix it and see what is left before going further.

Step 2: find out why the original failed

This is the step people skip, and skipping it is how a second computer dies.

  • Any sign of water at the module, in its connector or around where it is mounted? Modules mounted low in the cabin on many Honda and Acura models, or in the plenum tray under the windshield on many Volkswagen, Audi, BMW and Mercedes-Benz models, are in exactly the places water collects. If water got in, find the leak before anything else.
  • A shorted coil, injector or solenoid on the circuit that stopped working? On many vehicles the computer switches these directly, and an internal short in one of them can destroy the driver inside the computer. Replace it before the new unit goes in. See this post.
  • A recent jump start, battery change, alternator failure or welding repair? Voltage events damage electronics.
  • Chafed or melted wiring anywhere near the module or along the harness?
  • Rodent damage? It is more common than people expect and it is easy to spot once you look.

If something outside the computer caused the failure, that something is still on the vehicle.

Step 3: confirm it is the right module

Make sure you are replacing the computer that actually controls the thing that is broken. Lighting, locks and anti theft faults are usually the body control module, not the engine computer. Shift problems may be a separate transmission module, or may be handled by the same powertrain module that runs the engine, depending on the vehicle. Our post on what the names mean covers which is which.

Step 4: gather what you need to order

  • The full part number from the label on your unit, including the suffix letters at the end. Photograph the label rather than copying it by hand. If there are several labels, photograph all of them, because dealer software updates leave extra stickers behind, which is normal on Chrysler, Dodge and Jeep units in particular.
  • Your 17 character VIN, copied from the vehicle itself, not from paperwork. No letters I, O or Q appear in a VIN.
  • Year, make, model, engine and transmission.
  • Whether the vehicle is automatic or manual, because that can change the part.
  • Any options that affect the powertrain, such as four wheel drive or a California emissions package.

If the label is unreadable or the unit is missing, your VIN is enough. A dealer parts counter can look up what the vehicle was built with from the VIN in a short phone call, and so can we.

Step 5: know what happens after it arrives

  • Read the product page for your part and note any relearn steps for your vehicle.
  • Expect the first few days to feel slightly different while the computer learns your engine. See The First Week With a Replacement Computer.
  • Do not book an emissions test for the day after. The readiness monitors reset and need several days of mixed driving. See this post.
  • Read our warranty and policies pages so there are no surprises.
  • Ask about anything unclear before you order rather than after.

Step 6: order

Type your part number into the search box at the top of any page, or use the vehicle finder to browse by make, model and year.

If you get stuck at any point on this list, email Help@TheECUConnection.com with your VIN, the part number, your codes and what the vehicle is doing. We will point you at the right unit, or tell you that you do not need one.